Ashida Wii Portable

Stitches

2 and a Half Dollarydoos
Staff member
.
.
.
Joined
Feb 5, 2017
Messages
4,138
Likes
3,241
Location
Banana Bender Land, Australia
Portables
6
Throwing a link in there may be useful as well in case there's a revision or a new diagram gets made/etc.
You should be able to access the OSD by soldering a wire to a ground location and poking the + - menu source pins with it to form a rudimentary button
 

Hili

.
Joined
Oct 3, 2022
Messages
25
Likes
54
Portables
2x Ashida, 2x TinyTendo, 1x N64HHv2
You should be able to access the OSD by soldering a wire to a ground location and poking the + - menu source pins with it to form a rudimentary button
Ok thank you I will try that.
 

Hili

.
Joined
Oct 3, 2022
Messages
25
Likes
54
Portables
2x Ashida, 2x TinyTendo, 1x N64HHv2
It worked thank you very much for your help.
 

iabhua

.
Joined
Mar 22, 2022
Messages
6
Likes
1
There was some discussion about printing on an Ender 3. I was able to get it to print, although it was at a weird angle and there's some (slightly) rough parts where the supports connected. Overall its perfectly acceptable and I think it came out great.

Print info in case someone is interested:
-Printed on an Ender V2 (it barely fits, but will indeed work)
- Standard PLA filament
- Slicer software was Ultimaker Cura 4.13.1
- Using default setting for my printer model (setup using Cura's wizard) with two exceptions:
- Print Temp 205C (slightly higher than default)
- Print Speed slightly slower than default, I believe its a little slower than 40mm/s
-Printed on best quality (0.12mm)

If someone would like the Gcode I am happy to share.View attachment 21661View attachment 21662View attachment 21663View attachment 21664View attachment 21666
Bought myself a Ender 3... a bit late to the party ... I KNOW. Any chance you could share the gcode with me also?
 
Joined
Jul 20, 2020
Messages
19
Likes
8
Is the GC+ MP line connected to anything on the Ashida board? I would like to wire up a Switch rumble motor and it looks like I just need to connect it to M+/-, jumper LRA, and MP to 3.3v?
 

Wesk

Undervolting....
Staff member
.
.
Joined
Jul 12, 2017
Messages
922
Likes
2,405
Location
Queensland, Australia
Is the GC+ MP line connected to anything on the Ashida board? I would like to wire up a Switch rumble motor and it looks like I just need to connect it to M+/-, jumper LRA, and MP to 3.3v?
The rumble lines are not connected to anything on the Ashida boards. I believe all you need to do is bridge the 3.3v pad with the MP pad and wire your rumble device to M+ and M-.
 
Joined
Nov 4, 2022
Messages
1
Likes
0
I'll send you a gdrive link whn I'm of work

Heres how it turned out om my ender 3View attachment 19124View attachment 19125
Hello I know I’m super late but would you be able to send me the g code too?

There was some discussion about printing on an Ender 3. I was able to get it to print, although it was at a weird angle and there's some (slightly) rough parts where the supports connected. Overall its perfectly acceptable and I think it came out great.

Print info in case someone is interested:
-Printed on an Ender V2 (it barely fits, but will indeed work)
- Standard PLA filament
- Slicer software was Ultimaker Cura 4.13.1
- Using default setting for my printer model (setup using Cura's wizard) with two exceptions:
- Print Temp 205C (slightly higher than default)
- Print Speed slightly slower than default, I believe its a little slower than 40mm/s
-Printed on best quality (0.12mm)

If someone would like the Gcode I am happy to share.View attachment 21661View attachment 21662View attachment 21663View attachment 21664View attachment 21666
Hello, would you be able to send the G Code with me ?
 
Joined
May 10, 2021
Messages
14
Likes
35
Bought myself a Ender 3... a bit late to the party ... I KNOW. Any chance you could share the gcode with me also?
Hello I know I’m super late but would you be able to send me the g code too?


Hello, would you be able to send the G Code with me ?
Hi sorry I deleted the file by accident, I wrote to some people that I sent the file to before and hope they have it - I'll get in touch with you guys if I get hold of it again
 

Wesk

Undervolting....
Staff member
.
.
Joined
Jul 12, 2017
Messages
922
Likes
2,405
Location
Queensland, Australia
Is it possible to add HDMI Out to the Ashida and re-add the sensor bar port?
The stock sensor bar requires 12v which the Ashida doesn't have. You'd need to make a custom LED bar that runs off 5v.

There is room for a HDMI port above the LCD on the front of the case.
 
Joined
Dec 14, 2021
Messages
19
Likes
1
The stock sensor bar requires 12v which the Ashida doesn't have. You'd need to make a custom LED bar that runs off 5v.

There is room for a HDMI port above the LCD on the front of the case.

How would I do that I don't have a lot of knowledge of this stuff so any help would be really appreciated.
 

Stitches

2 and a Half Dollarydoos
Staff member
.
.
.
Joined
Feb 5, 2017
Messages
4,138
Likes
3,241
Location
Banana Bender Land, Australia
Portables
6
How would I do that I don't have a lot of knowledge of this stuff so any help would be really appreciated.
Look up any basic LED tutorial and apply the principle to 910-915nm diffused Infrared LEDs. You'll have to devise the mounting method yourself
 

Y2K

"The PS1 Guy"
Staff member
.
.
.
Joined
Apr 14, 2022
Messages
175
Likes
396
Location
Chicago, IL

Tak00

.
Joined
Nov 6, 2022
Messages
16
Likes
0
I was planning on getting the case done by PCBWay but I need the files, only the case, where can I get the files and for some reason, it needs to be ".rar"
 

Stitches

2 and a Half Dollarydoos
Staff member
.
.
.
Joined
Feb 5, 2017
Messages
4,138
Likes
3,241
Location
Banana Bender Land, Australia
Portables
6
I was planning on getting the case done by PCBWay but I need the files, only the case, where can I get the files and for some reason, it needs to be ".rar"
In the first post there are links to download the case files
 
Top