gamecube controller

  1. Yanis

    Question Question about Wii's GameCube Ports

    Hi, I have a small question, say you have a wire or a cable or something like this in your hand, if you want to add a switch or a board or whatever you want you'd just cut that wire or cable or whatever in half and solder both sides the switch or board or the whatever you want, how that would...
  2. Discussion Turning RP2040 Zero into a GameCube Controller

    Hello BitBuilt community, I'm thrilled to share a project that I've been working on recently. I've successfully transformed the RP2040 Zero into a functional GameCube controller. Building upon the foundations of the pico-rectangle project, I've taken it a step further by crafting a...
  3. Question GameCube Platinum Color

    Hello guys, Does anyone know what paint/hex color the platinum GameCube controllers are? I'm wanting to paint my Ashida like the controllers i grew up playing with. Worst case scenario I'll just bring a controller into Home Depot and just have them color match it. Thank you!
  4. WillF

    Custom GameCube controller PCB motherboard Commission Request

    Greetings! I bought this rare unique SpongeBob Edition Gamecube Controller last month that was heavily modified. The previous threw an OEM GameCube Controller motherboard in there which doesn't fit due to the different size and different lower start button location. I can't seem to find any...
  5. Skedaddlez

    Worklog GCShuffle

    Hey all, I've been gone a while and was only here very briefly. Life got busy and my previous project (a Wii portable) was put on hold until I am inspired. My current project may interest many of you though! I call it GCShuffle, a fun little board that is capable of mixing up Gamecube...
  6. aurzola

    Question Wii to microcontroller interface

    I want to send Some character data from homebrew app to a microcontroller to display on LCD module. Assuming no wifi. it is posible to use an output port from the wii like one of the gc controllers to read in on the microcontroller? The usb route is not posible as the microcontroller cannot act...
  7. Question Switching from BBloader to RVloader without a gamecube controller

    So I have bbloader installed on my Wii, and I want to switch to RVloader, but I don't have a gamecube controller. Also, I lost the usb I installed bbloader on so I most likely need a new one. What is the procedure I need to follow?
  8. Question Gamecube controller protocol

    So I got my DIY GameCube controller emulator to output a 1 and a 0. I can also receive stuff. I read that the console sends 000000001 to look for the controller. What should i send back to tell the console that I am there?
  9. Aaron Miller

    Question GC Joysticks

    From what I’ve been able to tell, in pretty much any Wii/GameCube portable, you’re going to have two joysticks: one main joystick and one c-stick. I was looking at the motherboard for a GameCube controller, and I saw that only the c-stick looked like it could be feasibly removed for use in my...
  10. DeoNaught

    Worklog }Side Project?{ Dream Machiine;

    So while I wait for my soldering heat gun to work(waiting for a replacement that works .-. ), and since I'm out of money, I decided to give my idle hands work, and I took a shot at Frankencasing. It sucks, But It's finally done the case work for the most part(just need to make port holes). I'm...
  11. Daquantrius Johnson

    Question DIY WaveBird Reciever?

    ey b0is, I was wondering, would it be feasible to make a wavebird receiver using something like this https://ns-electric.com/files/datasheets/NRF24L01P.pdf and a simple Wavebird protocol decoder (https://github.com/CFSworks/wavebird-reversing) and gcc encoder program on an arduino or some...
  12. Madmorda

    Guide Commonly Used Diagrams and Pinouts

    I'm not really sure where to put this, but I made a cheat sheet of helpful info so that I could stop looking these up every few weeks. I hope others find it useful as well :)
  13. moonDoctor

    Discussion Well doggone, PowerA beat me to it

    https://www.powera.com/us/gamecube/ Here I was ready to start my worklog about my joycon/wavebird combo I've lovingly dubbed the JoyBird, and PowerA has beat me to the punch announcing this today: I'm excited that someone finally made a GCN wireless for us casuals (c'mon Nintendo, Wavebird 2)...
  14. DeoNaught

    bt Modules, Wifi Modules, and a set of clear Gamecube buttons

    Hello friends, I'm selling some stuff, to clean out my desk, and get some money for my projects. I have a couple Wii bluetooth modules, and wifi modules(and antenna's). $2.50 for a module, plus whatever shipping is. I am also selling my set of Alibaba Clear Gamecube buttons for $10, but that...
  15. Biome

    Question Questioning the possibility of turning a Gamecube controller into a Joy Con, need help from veterans

    I'm new to this, but I think I understand it in concept. I just need some advice on how to go about doing this. Any and all advice one rewiring the buttons and joysticks is greatly appreciated!
  16. Joe DiCristo

    Question Help Me Design a Case? (Gamecube Portable)

    Hi! These past couple months I have been designing and building a gamecube portable. There are many things that need to be worked on and an enclosure for my project is no exception. I have access to a 3D Printer and CAD software, but I don't have a 3D scanner to scan the controller to get the...
  17. Fruity_Grebbles

    Question Anyone have a scan of a wavebird bottom shell?

    I couldn't find one online and don't have the means to scan it myself. It's a bit too organic to think about measuring and remodeling. If someone could take a scan, I'd appreciate it.
  18. John

    Gamecube Analog Stick

    Hello, I am looking to buy 2 grey GameCube Analog sticks. I looked on Ebay and Amazon, they all look cheap. Please let me know if you have extra you are willing to sell.
Top