- Joined
- Jul 9, 2020
- Messages
- 230
- Likes
- 501
Usually Mm. Pcbway has nice prints for utr clear and transparent resins. They will also paint for you. A bit pricy but really hard. Jlcpcb has nice white resin and SLS nylon and is alot cheaper.
Or someone you know can print for you… they will need the 3D model files that are posted on ashida cutting edge page.
Or someone you know can print for you… they will need the 3D model files that are posted on ashida cutting edge page.
iabhua
.
- Joined
- Mar 22, 2022
- Messages
- 6
- Likes
- 1
Thanks
Could anyone maybe help. I want to buy all the needed hardware from 4layertech but obviously they do not have the screens only the driver board. What type of screen (a specific model would help), would I need to buy separately and where is the best place to look for a IPS one?
- Joined
- Jan 23, 2020
- Messages
- 15
- Likes
- 7
Anyone know when the 4layertech site will have the ashida pcb set in stock?
- Joined
- Mar 31, 2022
- Messages
- 3
- Likes
- 3
Same looking forward to making a build as well, thanks for all your work!
roht
.
- Joined
- Apr 5, 2022
- Messages
- 2
- Likes
- 1
- Joined
- Mar 31, 2022
- Messages
- 3
- Likes
- 3
will be awaiting IPS and PMS2
MJMT
.
- Joined
- Apr 16, 2021
- Messages
- 100
- Likes
- 132
- Portables
- 2
Does anyone know if I shouldn't bother removing the U5 and the surrounding resistors if I'm using a RVL-PMS-2 since it can replace the U10 relocation function? I know there's a trace under it we usually sever as well during that process...
You don't need to remove U5 / surrounding components if you're using the PMS2 / Lite U10 emulation. The trace sever is only done if you want to test your U10 relocation pre-trim, but is not necessary at all once the board is trimmed.
MJMT
.
- Joined
- Apr 16, 2021
- Messages
- 100
- Likes
- 132
- Portables
- 2
PCBWay is telling me that the Right and Left Trigger mounts have a point where the thickness is only .5mm and they want to change it to .8mm. Does this sound right or did something get screwed up? I just set the design units to mm, Resin for the case and Nylon for everything else including the trigger mounts.
It'll print fine, PCBWay are just over cautious with these things.
iabhua
.
- Joined
- Mar 22, 2022
- Messages
- 6
- Likes
- 1
Will the 4layer driver board work with this display? https://www.buydisplay.com/5-tft-lcd-display-module-wvga-800x480-high-resolution-for-mp4-gps
It is the ER-TFT050-3 not the ER-TFT050-6? It comes as non Touch or Touch...
It is the ER-TFT050-3 not the ER-TFT050-6? It comes as non Touch or Touch...
- Joined
- Apr 12, 2022
- Messages
- 2
- Likes
- 0
Would this display work? because 4layer doesn't have the display in stock.
The panel looks like it'll be compatible with the driver board found at 4layertech.Would this display work? because 4layer doesn't have the display in stock.
- Joined
- Apr 12, 2022
- Messages
- 2
- Likes
- 0
Great Thanks!
Start your own thread, this is not the place to ask these things.
Luk3wrm
.
- Joined
- Oct 13, 2019
- Messages
- 3
- Likes
- 0
Hey I was struggling to find the screen component for this build I stumbled across these the driver board looks identical I'm just not sure if ips has anyone brought one from and had any luck all the tech drawings look the right one
www.buydisplay.com
5 inch LCD Screen TFT Module,800X480 VGA Video AV Driver Board
ER-TFTV050-3 is 5 inch LCD screen touch display module in 800x480 resolution with VGA,dual AV signal driver board for portable products,Industry and security.
www.buydisplay.com
The screens are currently in stock at 4layertech.comHey I was struggling to find the screen component for this build I stumbled across these the driver board looks identical I'm just not sure if ips has anyone brought one from and had any luck all the tech drawings look the right one
5 inch LCD Screen TFT Module,800X480 VGA Video AV Driver Board
ER-TFTV050-3 is 5 inch LCD screen touch display module in 800x480 resolution with VGA,dual AV signal driver board for portable products,Industry and security.
