Recent content by FatBaldDad

  1. FatBaldDad

    PS2 Ultra Slim

    @Zhain92 Even if you found a GH-061-xx you would still need to solder. Do you have the soldering iron?
  2. FatBaldDad

    PS2 Ultra Slim

    Just sifting through some posts trying to find a few examples. I have some boards taht I have made but I know that does not help you. I am working on a store to make my mods available, but not yet. You can use the switch board (SW Board).
  3. FatBaldDad

    PS2 Ultra Slim

    This is not an issue. You have probably have a GH-062-xx? Can you send a pic or share the board model? Look through these posts, should help you. https://bitbuilt.net/forums/threads/ps2-ultra-slim.5077/post-69941 https://bitbuilt.net/forums/threads/fbd-ultra-slim-buildz.7216/post-75702
  4. FatBaldDad

    Worklog FBD Ultra Slim BuildZ

    Well, it's been forever since I've updated this thread. Man, time flies! LOL I've been pretty busy behind the scenes developing both hardware and software for these little consoles, and I'm still nowhere near finished. I think I'm going to rename this worklog to "FBD Ultra Slim BuildZ", since...
  5. FatBaldDad

    PS2 Ultra Slim

    I just took Wesk's original STEP and removed the MX4SIO part for ya, see if that works.
  6. FatBaldDad

    PS2 Ultra Slim

    I've only used the resin printing option from PCBWay, but I've done a handful of shells that way. With resin, you can't use traditional heat-set threaded inserts like you can with FDM prints. I've been using the original screws from the 79K shell, and they work fine. The downside is that you...
  7. FatBaldDad

    Mini PS2 Slim Build

    Hey!! how ya been? That design has changed and will change again, lol. I picked up some tan caps a while back but I will be adding more to this design. 1) The interposer board will be expanded to allow for an additional Flash chip (20Mb of flash) - I am not sure yet but if I have acess to...
  8. FatBaldDad

    PS2 Ultra Slim

    Pins 4 and 8? I think you want 4 and 5 for the Power On 4 - GND 5 - PWR_SW https://bitbuilt.net/forums/threads/fbd008-ultra-slim.7216/post-75702
  9. FatBaldDad

    PS2 Ultra Slim

    Here is the reason from Wesk: https://bitbuilt.net/forums/threads/ps2-ultra-slim.5077/post-69652
  10. FatBaldDad

    PS2 Ultra Slim

    Q: Is there an STL file for an Ultra Slim shell that keeps the second USB port? A: There are a few different Ultra Slim variations out there, including some in this thread, but I haven’t seen one that keeps both original USB ports. Some designs add a USB-C, usually for power in the rear. You...
  11. FatBaldDad

    PS2 Ultra Slim

    @Densarc There is not enough room. You can read a little from here. https://bitbuilt.net/forums/threads/ps2-ultra-slim.5077/post-69650
  12. FatBaldDad

    PS2 Ultra Slim

    Use https://ps2homebrewstore.com/ Setup your card following the instructions there. Yes, you can use a 256Gb mSD card. Would be best if its an A2. The cards that ship with the PSXMCG2 are good for just game saves but for exploit, game storage and game saves you do need a better card.
  13. FatBaldDad

    Worklog FBD Ultra Slim BuildZ

    I do it differently, this build is actually finished. I keep coming back to fill in the gaps, lol. On this build I used a dev board. Now I have my own board. I I went with a more universal approach, has the boot/reset buttons, UART interface, and OLED. I put the pads together so you could...
  14. FatBaldDad

    PS2 Ultra Slim

    Very interesting. When I get some time Ill look into it some more just out of curiousity. Have fun!
  15. FatBaldDad

    PS2 Ultra Slim

    @ImCriptix That chip is the Mechacon, if that trace is tied back to the Optical drive then maybe not. I would have to investigate that further. If the board powers on and ou have a dsplay. See if you can drop in a FMCB and MX4SIO and try to see if a game loads. Or repair the trace.
Back
Top