Recent content by ShockSlayer

  1. ShockSlayer

    MGC 2022

    I remember the big pig from last year, now there's a smaller second pig....perhaps by 2023 we'll have a third, even smaller pig. I wasn't there and have no pictures, but cheese took one just for me and I'm excited for it to be posted.
  2. ShockSlayer

    Ghosts 64rced to come out of retirement for one last job

    Oh yeah, while I'm actually on the forums. I've got like, a whole ass video script written, but basically since getting back from MGC with this thing it's taken a bit of a backseat. I'll almost definitely bring it to the next one, so maybe around that time I'll revisit the idea of making a...
  3. ShockSlayer

    Board scan N64 Rev 9-1 Compendium

    Download - Full size (.PDN) Get Paint.NET So, this was something I was working on back in the day. I was planning to clean it up a bit more, get things more sorted and labeled, add more revisions, etc. - but that never came to fruition. There's one major difference between this compendium and...
  4. ShockSlayer

    MGC 2021 - Bringing BitBuilt Back

    So this is the unit I built - very peanut N64 laptop. It managed to run the whole time with no issues, the bottom barely got warm so I'm pretty satisfied with the MGC stress test - not all the portables I've built have been that lucky. Like the display says it was assembled mere hours before it...
  5. ShockSlayer

    Ghosts 64rced to come out of retirement for one last job

    Are you ready now? To witness a power not seen for thousands of years?
  6. ShockSlayer

    Question Help with an N64 board: no video/audio output, no Everdrive64 LED activity

    Did they turn it on while it was in that previous state? If so it's probably toast. With no cart in, I think you can turn it on and feel the chips - if they heat up too fast it's probably unusable now. The LED turning on just means that the 3.3v line exists/isn't shorted, it's not any kind of...
  7. ShockSlayer

    Ghosts 64rced to come out of retirement for one last job

    this pig is japanese, but drug free
  8. ShockSlayer

    Worklog SparkleBear's First Portable Nintendo 64 Build Project Worklog.

    Try disconnecting the RGB board(and probably leave it disconnected until you can get the controller stable again.) If it's still being troublesome shorten any wires that you can, and clean up the affected areas on the off chance there's some loose/lodged junk. Lastly, you could try swapping the...
  9. ShockSlayer

    Ghosts 64rced to come out of retirement for one last job

    basically done with the case design, save for the inevitable tweaking after I finish another round of test prints. I did figure out what was ailing my printer, turns out cooling fans are important. didn't even know mine went missing. 3d printing is my passion Saving the spiciest stuff for last...
  10. ShockSlayer

    Ghosts 64rced to come out of retirement for one last job

    it's just the PLA. if I take off the middle part the squeaking goes away. wd40 is pretty delicious but probably not what I'd want to use for this if the hinges were oinking
  11. ShockSlayer

    Ghosts 64rced to come out of retirement for one last job

    another win for the league of those who much prefer shelled clams printer used to work perfectly. no idea why it's being such a peanut these days. probs gonna go with JLC for the final once I can confirm all my designs aren't equally peanut. otherwise been doing lots of designing and minor...
  12. ShockSlayer

    Ghosts 64rced to come out of retirement for one last job

    You wanna explain to me how tf I'm gonna make a non-clamshell laptop, Nold? You greasy motherfuckers makin' tablets now? I leave for 5 minutes and this shit. Who started this??? Was it Shank? I knew that little Wiiner was up to no good. MGC 2021 it's goin' down. DUKES UP
  13. ShockSlayer

    Ghosts 64rced to come out of retirement for one last job

    Airflow tests are coming along nicely. This isn't even the fan that I ordered...
Top