BC-250: The Steam Machine with the PS5 APU and AIO Water Cooling

Joined
Feb 16, 2025
Messages
23
Likes
23
Location
FRANCE
Portables
3
miniature.webp

Hello everyone,
I’m presenting my new completed project: repurposing the BC-250 card, formerly used for Ethereum mining, into a Linux Bazzite Steam Machine.

I'm going to use the Thermalright AQUA ELITE 240 White ARGB AIO liquid cooler to properly cool the APU, which runs very hot since it's the PS5 Fat APU fabricated on a 7nm process.
The cooling solution here is critical because I'm not using liquid metal the way Sony does in its PS5. Once the 40 CUs are unlocked and the 8 cores / 16 threads are unlocked and clocked at 2200 MHz for the GPU and 3.8 GHz for the CPU respectively, the thermal issue is worse than on a PS5 Fat.
Indeed, the PS5 can dissipate its heat more easily thanks to a 30 × 40 cm motherboard, whereas the BC-250 is only 30 × 15 cm.
Cooling just the APU isn't enough — the entire card needs to be cooled, so in addition to the AIO I'm using two 1.5 cm wide Thermalright C12015W-S fans blowing on both sides of the card, i.e. over the VRMs and the VRAM.
I also had to 3D print a custom case in PLA, since the cooling is very well controlled and it only reaches 40–45 °C under full load.
The airflow is designed as follows: fresh air enters from the sides to cool the card, then it's drawn upward to cool the AIO radiator, and finally expelled out of the case through the top.

Since the card is atypical, there's no official adapter for mounting an AIO water cooler, but I found a 3D model already made by the community — and there are versions that fit any AM4, AM5, or Intel LGAxxx cooler.

NexGen3D AIO Mount for the BC-250: https://www.printables.com/model/1554003-nexgen3d-aio-mount-for-the-bc-250/files
carte7-xclamp+braquet.webp


I've also added an ESP32-S3 N16R8 to this project, which displays real-time CPU/GPU temperatures and (load)utilization via HWMON.
FPS, GPU and CPU clock speeds via MangoHud, and upscaling info via HelixSR (the log file it generates provides these details).
The ESP32 also controls the speed of the side fans and has three PWM speed levels for the pump, depending on whether you're in emulation mode or playing AAA PC games.
Allowing the pump to not run at 100% all the time helps prevent wear on its circuits.

The ESP32 can also display the name of the game and its cover art — whether it's a PC game or an emulated ROM.
Simply reading the running process tells you which emulator is active and therefore the type of emulation (PS2, Wii, GameCube, arcade, N64, etc.) and the name of the ROM.
Finding the cover art is straightforward since it's already stored in a folder managed by the frontend: EmulationStation (gamelist.xml).

A Python script runs continuously at startup and sends the info to the ESP32.
A small speaker plays the MP3 that characterizes the boot sound of the emulated console each time a game launches.
This MP3 file is stored on the SD card of the IPS screen connected to the ESP32, and the digital audio is decoded to analog mono via a MAX98357A.
The 4" capacitive touchscreen IPS display is connected to the ESP32 via a 14-pin FPC board.
carte12-panneau-avant.webp
carte13-panneau-avant.webp


The BC-250 already has everything a PC needs: motherboard, CPU, GPU, RAM, 1 GbE ethernet, 2 USB 2 ports, and 2 USB 3 ports.
It's just missing a 500 W power supply and storage in the form of an M.2 NVMe SSD.
To power all of this, I also had to design a small relay board that takes 12 V from the PSU to power the two fans and the pump, and 5 V for the ESP32, the LED strips, the MAX98357A, and the 4" IPS screen
carte relai.webp
carte10_carterelais.webp

carte11_carterelais.webp


For the LEDs there are 6 strips in series:
  • the front face, like on a Steam Deck
  • the two side fans
  • the two 240 mm AIO fans
  • and the pump
Since the ESP32 only provides a 3.3 V signal for LED animations, it can only drive 2 LED strips.
So, I level-shifted the 3.3 V signal up to 5 V using a 74HCT14.
The PCB was designed in EasyEDA and fabricated using the UV method followed by ferric chloride etching.
I then protected the copper traces from oxidation with red UV paste.


Capture d'écran 2026-11-17 004954.webp

The AIO is heavy, so I had to create an aluminum skeleton — it's made of 1.5 mm thick aluminum angle brackets with 3 × 2 cm fins, for a total length of 4 × 30 cm.
I also added a 4-port USB 3 hub on the front.
Case dimensions: 33.3 cm long, 25.5 cm tall, and 19.2 cm wide.
The fully assembled case weighs 5.5 kg
Capture d'écran 2026-11-17 004259.webp
Capture d'écran 2026-11-17 004327.webp
Capture d'écran 2026-11-17 004417.webp

Capture d'écran 2026-11-17 004352.webp
Capture d'écran 2026-11-17 004244.webp

The BC-250 will run Bazzite in Deck mode with Steam launching at startup, so once everything is configured, all you need is a controller to use it.
Of course, you can switch back to keyboard and mouse if you prefer to play that way, or use the BC-250 as a multimedia player, browse the web, check your emails, work — basically just like a regular PC!

To see what it looks like in action, here's my YouTube video presenting my BC-250. It's in French, but you can enable the English subtitles:
 
Last edited:
Back
Top