Worklog My first GCp

Joined
Mar 26, 2016
Messages
137
Likes
190
This may be a shot in the dark, but why not clamp it down with a rubber clamp then, once you have sufficient pressure, epoxy it to the board to ensure that the pressure remains constant.
I already tried it but there is no equal presure on the entire connector. I think that a better solution is have another megadrive :c
 
Joined
Mar 4, 2016
Messages
5
Likes
0
I already tried it but there is no equal presure on the entire connector. I think that a better solution is have another megadrive :c
You may be right, and I think they are on back order from badassconsoles. You could try posting in the buying/selling section?
 
Joined
Mar 26, 2016
Messages
137
Likes
190
Importante update!
Finally! I made it works!

my wasp fusion works flawlesly!, now the controller with "maybe" auto turn off when i connect the first player on my "gamecube multitap"

Ps:
I forgot to vive thanks to providencial for the megadrive
 
Last edited:
Joined
Mar 26, 2016
Messages
137
Likes
190
UPDATE

I have a short time to work in the console right now, I'm creating a 3d printing service to sell so need to keep the webpage and capture clients.

so..
IMG_20160418_020424.jpg
IMG_20160418_020436.jpg


I relocated once again que " modular multitap" connection .

IMG_20160418_023927.jpg


and also re-rewire the usb connector because lastly i was having a lot of problems with it. so...

IMG_20160418_025049.jpg

to.

IMG_20160418_043852.jpg


IMG_20160418_023933.jpg


ps: the blue metal thing in the middle of the table (nearly the sd) is the "trompe" the musical instrumenta dat plays the "toing" sound hahaha
 
Last edited:
Joined
Mar 26, 2016
Messages
137
Likes
190
Hi guys. here with a little "problem"


When the gc autoboots on swiss the screen turns white like un the video and i can navigate but blinded.

If GC autoload and run swiss over replay menú nothing wrong happends.

I checked que swiss resolución and tried in 480i, 480p and auto and its the same
 

Aurelio

ᕕ( ᐛ )ᕗ
Staff member
.
.
.
.
.
Joined
Mar 3, 2016
Messages
2,219
Likes
2,937
Portables
2
Ok then can you try it on another monitor or a tv? If you get the same error can you try to load the swiss updater? It should be easier to load it if you put only that in your SD card :D
Also check if you have connected something to the DetectCable pin of the digital output by mistake (see http://gamesx.com/wiki/doku.php?id=av:nintendodigitalav for reference). If the gamecube sees an high level on that pin then Swiss automatically output 480p that doesn't work on composite video.
 
Joined
Mar 26, 2016
Messages
137
Likes
190
Update number... I dont know

working in the final audio solution for my portable.
I will use the 3ds volume potenciometer to get lower or higher audio.
Actually i have 2 audio amps for every channel because the Hxj8002 chip audio output is mono.
IMG_20160426_021731.jpg



the screen part with amplifiers finished, only i need to close all and make the expansion case for screen.
IMG_20160426_223524.jpg

here is a little video...


i have a little question about sound amp

If I relocate que audio after the gamecube's audio amp(on output), i need to put 5v on it to have sound?
 

bentomo

sands mobos in a single swipe
.
.
Joined
Jan 28, 2016
Messages
91
Likes
48
This one is starting to look pretty sick!
 

ShockSlayer

the real
.
.
Joined
Jan 16, 2016
Messages
1,512
Likes
3,940
Location
standing up
Portables
please do not ask!!!! I will NOT respond
If you're grabbing audio directly from the AVE-DOL then you don't need to put 5v anywhere.
 
Joined
Mar 26, 2016
Messages
137
Likes
190
If you're grabbing audio directly from the AVE-DOL then you don't need to put 5v anywhere.
sure, but i would like to get a little more power on sound output but the amps works fine with 5v. i was thinking that if i apply Tchay's audio fix maybe i'll have more volume for speakers cause they are a little slow
 
Joined
Mar 26, 2016
Messages
137
Likes
190
soon i'll update my worklog.... need to whow you a little things :B
 
Joined
Mar 26, 2016
Messages
137
Likes
190
I really would like to continue this portable. but i dont have time and money :'(
 
Joined
Mar 10, 2016
Messages
62
Likes
43
Location
Chile
Today Panchuflenks stopped by my work and picked up a TI regulator he needs to continue with this project!

He has also gotten over a filament drought for his 3d printer.

Please all bully (or encourage?) him to get back on the portable!
 
Top