Worklog Miceeno's N64 Portable

Miceeno

.
2020 3rd Place Winner
Joined
Nov 30, 2016
Messages
153
Likes
281
Portables
6
It's done.

01-Front.jpg





This contest is a good motivator to finish this N64 I have with an UltraVGA. My primary objective is to build a ghetto single board N64. Since I don't have the experience designing custom PCB's I will just glue stuff together. I should probably just buy Eagle and spend a couple of hours learning it but I've already started this the ghetto way.

So far I have the following parts:
--Rev05 N64
--5 inch VGA Screen and Board
--Red Board Battery Board
--4x Panasonic 3400mAh
--18650 Battery Holder's
--UltraVGA
--24 Pin DIP to FPC (because I'm lazy and don't want to solder directly to the UltraVGA)
--PAM8803 Audio Amp
--08080808080808080 Ti Regulators (3.3v and 5v, I'm not relying on the low dropout regulator for 5v because it drops out around 6.8v and the batteries aren't depleted until 6v)
--A chunk of PCB from a Router that has a push button switch, barrel jack, and a tact button

So here's what I have so far:

Main Board.JPG


Main Board Back (cropped).jpg


VRM 3.JPG


UltraVGA Solder 3.JPG


Screen Controller Close.JPG


Audio Amp 2.JPG


Red Board 1.JPG


Power Switch 1.JPG
 
Last edited:
Joined
Dec 10, 2016
Messages
578
Likes
663
Location
Constant Fear
Portables
sin^2(x) + cos^2(x) +e^(i*pi)
Btw, there's a free version of Eagle, which about everyone here uses. and then you have Kicad, which I use along with some other members, I learned How to use it in like three days(I used a video), It'll probably take you less, since you have more experience with with console modding. :)
 

Miceeno

.
2020 3rd Place Winner
Joined
Nov 30, 2016
Messages
153
Likes
281
Portables
6
I'll have to look into Eagle. Last I checked (years ago) the free version was limited to 2"x2" single layer, single side. I'm not as poor as I used to be so I don't mind buying a liscence to good software. My only hesitation would be crossplatform support as I'm trying to get away from Windows.
 

BocuD

.
Joined
Jul 21, 2016
Messages
468
Likes
605
Location
The Netherlands
Portables
3
I'll have to look into Eagle. Last I checked (years ago) the free version was limited to 2"x2" single layer, single side. I'm not as poor as I used to be so I don't mind buying a liscence to good software. My only hesitation would be crossplatform support as I'm trying to get away from Windows.
Well about that.. Eagle runs on Winblows, Mac and Linux, so getting away from it won't be a problem. ;)
Portable is looking amazing btw, its so neat.. Can't wait to see it finished!
and lose the contest to it if I ever finish mine
 

GingerOfOz

no wario
Staff member
.
.
2020 2nd Place Winner
2022 3rd Place Winner
Joined
Dec 16, 2016
Messages
1,121
Likes
2,689
Location
The Oregon Wildlands
Portables
just so many i am so cool
I'll have to look into Eagle. Last I checked (years ago) the free version was limited to 2"x2" single layer, single side. I'm not as poor as I used to be so I don't mind buying a liscence to good software. My only hesitation would be crossplatform support as I'm trying to get away from Windows.
Eagle is a bit more giving with their free version nowadays. Now you're able to make 2 layer boards, use both sides, and I'm not sure what the maximum board size is but I've never even come close to touching it. Also if you're a student, then you can link your student email and get the full version free for two years. Haven't bothered to do that yet since the free version has everything ai need right now.
 

Miceeno

.
2020 3rd Place Winner
Joined
Nov 30, 2016
Messages
153
Likes
281
Portables
6
Oops, I forgot to post these when I finished machining them. They're still a little dirty and are impossible to keep clean any way (finger print magnets). I made some mistakes along the way but didn't want to scrap the whole part so I "fixed" them. I did this on a manual milling machine without much of a plan except taking measurements off the main board and front board and test fitting as I worked. I probably should have taken the time to CAD/CAM the project and run it on one of the CNC milling machines but keeping with the spirit of a ghetto single(ish) board N64 Portable I figured I'd just wing it.

I whittled this case from two 1.25"x6"x9" pieces of 6061 aluminum bar and one piece of 0.125" of 5052 aluminum sheet. I had to JB weld some brass screw posts in the front half after the fact because the front board flexed way too much when buttons where pressed. Then I also miss measured the holes to screw the back half to the N64 stock heat-sink mount. Another part I screwed up was I had some chatter when relieving the analog stick area but left it because I sort of looks cool (I also didn't leave enough material on the bottom portion so there is a small hole). And finally I broke the tap on the last hole on the back half of the case. So I had to use a trepan cutter to extract the tap. So that was filled with JB weld and re-tapped. Like I said I made some minor mistakes but fixed them well enough to get the job done.

Also, this is probably the first aluminum portable this community has seen (outside of BenHeck and DarkUncle33 360/PS3 laptops). So I'd like to point out how I engineered the case to be one big heatsink in case it wasn't obvious.


Front-2.jpg


Front-Inside-2.jpg


Back-3.jpg


Back-Inside-3.jpg


Back-Plate.jpg



Here's it put together. The final dimensions are: 8.75"x5.25"x2.35". This thing is THICC


Done-Front-5.jpg


Done-Up-4.jpg
 

Madmorda

Painting Queen
.
.
Joined
Oct 27, 2016
Messages
725
Likes
1,718
Location
Texas
Portables
2
WHAT IS THIS SORCERY?! I can't believe you made that. I can't even wrap my head around how you got it so detailed and perfect. Seriously awesome work :D
 

MRKane

.
2021 3rd Place Winner
Joined
Nov 5, 2017
Messages
405
Likes
488
Excuse the delay as I collect the mechanism for my dropped jaw and get around to commending you on that case work! It is seriously something else and I dearly hope you don't paint it but keep it as a testament to what it truly is!
Also: I work developing trackers for various sports events, sailing, surfing, car racing etc. and you know what I really like? Well made hardware that you could beat someone to death with...or just hammer in nails...yeah...I'll go with "nails".
 

Miceeno

.
2020 3rd Place Winner
Joined
Nov 30, 2016
Messages
153
Likes
281
Portables
6
Thanks guys.

It's done.

It's heavy but extremely solid. So far I've been able to get 4.5 hours of battery life (the low battery LED turns off when there's 1 hour left). The only things I wasn't able to get 100% in time for this contest was attaching the Expansion Pak to the case's built in heat sink and one battery bank has to go in upside down to fit better.

13-Internal.jpg


14--Internal.jpg


15--Internal.jpg


16--Internal.jpg


01-Front.jpg


03-.jpg


05-.jpg


07-.jpg


10-.jpg
 

BocuD

.
Joined
Jul 21, 2016
Messages
468
Likes
605
Location
The Netherlands
Portables
3
Looks really nice if a bit chunky. And damn that video is good.. Also how did you get the assembly done so fast? It blew my mind lol
 

Miceeno

.
2020 3rd Place Winner
Joined
Nov 30, 2016
Messages
153
Likes
281
Portables
6
Looks really nice if a bit chunky. And damn that video is good.. Also how did you get the assembly done so fast? It blew my mind lol
I designed this to be easy to assemble and disassemble. It takes about 10 minutes (I did it once off camera before I filmed it). My only regret is the hot glue on the indicator leds and volume buttons. That part takes forever to assemble and disassemble. One day I'll swear off the hot glue.
 

Downing

Basement Owner
.
Joined
Apr 5, 2016
Messages
130
Likes
369
Portables
20ish...
Nice job man! Amazing video work as well, that had to have took some time!
 
Joined
Jul 4, 2017
Messages
125
Likes
108
I really like that you basically have it setup with two main boards that sit on top of each other, then the stuff in the back. Looks really easy to assemble and keeps it clean.
 
Top