Model [Guide / Release] Noldendo Wii Miicro - v1.1
So, Im putting together my DigiKey order, and the only things I have left are the barrel jack and power supply, and I'm not quite sure I understand how the measurements work. In the guide, what does the 8mm mean for the barreljack, is that the outer diameter, the depth? I just want to make sure I don't end up having to make a second order
Yes. The Wii needs the U10 to boot, so relocation is necessary.
vcesne
.
- Joined
- Nov 8, 2020
- Messages
- 9
- Likes
- 6
Thank you for your answer.
I have lost my U10 chip. Is it to possible to buy another one somewhere?
you can use the U9, too. I have a lot of them, if you are from europe. Otherwise somebody on discord might help you out.
vcesne
.
- Joined
- Nov 8, 2020
- Messages
- 9
- Likes
- 6
I destroy the U9 too when I trim the board. I am from France. I send you a PM.
Custom regulators, an explanation and guide | BitBuilt - Giving Life to Old ConsolesAre you able to provide what value resistors you used for the regulators? I'm keen to try building one of these
Although I'd recommend you use an RVL PSU instead of PTH regs.
vcesne
.
- Joined
- Nov 8, 2020
- Messages
- 9
- Likes
- 6
The value resistors are on this guide : https://bitbuilt.net/forums/index.php?threads/custom-regulators-an-explanation-and-guide.754/Are you able to provide what value resistors you used for the regulators? I'm keen to try building one of these
Big thanks for Swiss by the way
Hey emu, nice to see you around [don't know if you remember me from gcforever back in the day - lol] - Feel free to PM me if you have any questions/problems.Thanks, and yeah I should've mentioned I'd seen that page but was unsure what actual value resistors were used instead of those super precise resistances. I'll just buy some RVL-PSU instead - see you all in 2 months when they arrive
Thanks, and yeah I should've mentioned I'd seen that page but was unsure what actual value resistors were used instead of those super precise resistances. I'll just buy some RVL-PSU instead - see you all in 2 months when they arrive
these are the resistor values im using on mine
- Joined
- Apr 13, 2016
- Messages
- 4
- Likes
- 3
Yup I definitely remember youHey emu, nice to see you around [don't know if you remember me from gcforever back in the day - lol] - Feel free to PM me if you have any questions/problems.
I also just realised I'd bought a RVL Power Management System a while back, I might use that if it's possible to do so without a battery.
Seems to be possible, but you would need to butcher that nice PMS: https://bitbuilt.net/forums/index.php?threads/pms-to-psu-mod.3781/Yup I definitely remember you
I also just realised I'd bought a RVL Power Management System a while back, I might use that if it's possible to do so without a battery.
FYI: The Audio Amp can be driven with 5V it will just be quiter. wii2hdmi also just needs 5V [actually 3v3 but they have their own regulator onboard]
Emetsys
.
- Joined
- Jun 3, 2019
- Messages
- 142
- Likes
- 118
My bad, I should have check my infos, thank you.
To be a bit more explicit, you would need to either bridge the 2 pins on the U3 (enable and vin pins, could be done on any regulator, but easier on the boost one), or put 5v on the resistor near the PIC (could be found on top of C26 ie).
To be a bit more explicit, you would need to either bridge the 2 pins on the U3 (enable and vin pins, could be done on any regulator, but easier on the boost one), or put 5v on the resistor near the PIC (could be found on top of C26 ie).
- Joined
- Jan 26, 2021
- Messages
- 2
- Likes
- 0
I haven't started my built yet, but I want to get everything right in my head. I can't seem to find where the mote sinc button comes from, not on this page, the 4 and 6 layer trim guides.