70006 ps2 portable

Joined
May 24, 2018
Messages
47
Likes
55
Location
CHINA DALIAN
Hello everyone, I haven't released the PS2 I made. I've made a lot of them, most of them use wiiu shell. This time, this machine uses 70006 motherboard. I know it's very big, but not everyone owns a 7900x machine. In fact, 7W machine is also feasible, but its power consumption is relatively large, and the problem of heat dissipation and power supply is more troublesome. This one is plug-in game Strictly speaking, it's just half a handheld game console, using an HDMI adapter connected to an 8-inch LCD screen. As for cutting, you only need to cut from the handle to the edge, but you need to pay attention to the USB part, where problems are easy to occur. Once it is not started, you need to measure most of the resistance from PS1 to ps15. The reset point can be found near the largest chip in the lower right corner by measuring. Through my test, I use a 10000 Ma lithium battery, which can run for 2 hours. In the future, I will improve it and put the battery in. Its shape imitates the siwtch Lite, uses the PSP button, and the PCB is customized, as well as a lot of welding wires. In short, if you are interested, I can share my experience.
1605076646152.jpg

1605076646159.jpg
1605076646170.jpg
1605076712806.jpg
1605084425341.jpg

1605076885923.jpg
1605077225907.jpg
 
Joined
Sep 21, 2020
Messages
65
Likes
118
Location
Melbourne, Australia
Portables
1 (Aran)
im interested in how you hooked up the controls to the PS2, as i don't see a ps2 controller board in the internals.
 
Joined
May 24, 2018
Messages
47
Likes
55
Location
CHINA DALIAN
im interested in how you hooked up the controls to the PS2, as i don't see a ps2 controller board in the internals.
OK, actually, the controller is under the motherboard. The diagram you see is not finished. There are many lines. I didn't take pictures. The controller IC I used is very small. It can be customized in China, but it needs a minimum order of 2-3000. Please see this picture
1605085254309.jpg
 
Joined
Sep 21, 2020
Messages
65
Likes
118
Location
Melbourne, Australia
Portables
1 (Aran)
the controller ic would be usefull for the PS2 design im working on, but i don't think i need 2-3000 of them
 
Joined
Jan 18, 2020
Messages
43
Likes
10
It would be great to see a breakdown of your build including your custom pcb's
 

xck

.
Joined
Aug 28, 2017
Messages
17
Likes
62
OK, actually, the controller is under the motherboard. The diagram you see is not finished. There are many lines. I didn't take pictures. The controller IC I used is very small. It can be customized in China, but it needs a minimum order of 2-3000. Please see this pictureView attachment 14975
芯片用完可以找我 我还有500片左右
 

xck

.
Joined
Aug 28, 2017
Messages
17
Likes
62
Hi XCK, please translate to English before posting. Thank you.
OK I don’t speak English. I use translation software. I reply in Chinese because he is also Chinese
 

Aziz

.
Joined
Dec 10, 2022
Messages
1
Likes
0
Hi ! I know I may be a bit late but, I have a a ps2 75004, and I would like to do it portable like your ps2, what did you do to the motherboard ? like did you basically put a 10000mha battery in it and power up the ps2? did you made some modification to the motherboard ? (any trim or else ?)
 
Top