Hello everyone, given that this is my first PS2 portable project, I wanted to know some tips on how to do this at both the video level and the sound level. First of all, at the time I wanted to increase, and to decrease the volume using keys without a potentiometer, only keys I wanted to know...
So I have just received a ps2 model 79001(the mobo layout is more like 79003 however). I applied DC power of 8.5v to the positive pin of the barrel jack and the negative to a ground near a mounting hole on the motherboard. So far I have been unable to get even an a red standby LED to show. I've...
From the department of "don't worry, I'm dumb enough to give it a go"; I've put JLCPCB hard at work
This outline is for 7" 800*600 displays such as A070SN01 etc. I did alternative bottom tiles dimensioned for the 6.5", 800*480 AT065TN14
All broken up into <10x10cm tiles to take...
Working on two ps2 portables atm started the second due to the fact im waiting on the case and my Dremel set to finish the first one.so far I made a few awesome discoveries on the 2nd portable though!
all images are from the second project which uses a 50001 motherboard. ( hit a brick wall...
Hello all,
So typically I've finished my PS2p and was left thinking "I wish the insides were cleaner" and then had a crazy idea that'd require me to make my own PCB for handling the controller to come up with a solution. Simple question:
-Are there any PCB files for the PS2 controller freely...
Hey everyone!
I've been lurking for a while now and I have decided I'm finally going to start a worklog!
I'm not sure what I'm going to call this one (you Wii people have good names I'm jealous) but here's what it's going to include:
6 18650s, adding up to a 10200 Mah 7.4 volt battery pack...
So I was taking stock of the carnage on my workbench after the last PS2 portable when I started thinking about a project I'd been tinkering with, which was a Raspberry Pi portable inside a Wii U. See I'd collected most of the stuff to do it, I had the screen, and the external phone charger I...
Hi, how are you? I want to create a ps2 portable, but I'm new and I don't know a lot of how to cut the motherboard, I would like if someone could help me. Here there are some photos of my ps2 motherboard
While playing with this setup I was taking some notes an though compiling this into a step by step guide would benefit the community more than sitting on my laptop so after a bit of effort there it is.
This guide will help you setting up a Raspberry Pi to stream games to a PS2.
The point of...
So after a short break of… around 4 years I finally got the time/ motivation to finish my PS2 portable.
I couldn’t stand seeing this half finish case staring back at me, like a ghost of the modding past (see what I did there), begging to be completed.
For reference this is the link to old post...
So I'm halfway through building my first portable PS2. I need some advice on how to extend the ribbon cable on the disk drive, the one that goes to the laser. One of the guides I was using on modretro said there's a way using spare sockets to clamp two ribbon cables together but I haven't found...
I have been kept away from playing my PlayStation 1 and 2 games by the fact that I dislike the controller. I think that the left joystick should go in the top left as in most controllers (Xbox, gamecube, 3ds, etc) and I think that its placement on Sony controllers is very uncomfortable. To solve...
I need some help deciding which portable to make next so I figured I would reach out to all my fellow modders here to give me some guidance. :)
I'm currently working trying to wrap up my first GameCube "Simi" Portable project but have already gotten the parts for some of my next endeavors. I...
Had a few of these laying around. They've been tested to work with several computers, and even my Wii. If anyone wanted to include a keyboard in their next portable, or maybe just have a pocket-sized one to keep with your handheld, these are your best bet.
http://www.ebay.com/itm/142076923909
NOTE: My terms are more then reasonable and I pay very well for quality work. my budget for this project at present time is 2000 USD
Here is my design for both the front and back of the unit if you are up to the task and accept the below terms pm me.
Requirements are as follows:
Consistent...