ps2

  1. Soulheaven

    Question HELP RESET AND IGNITION KEY DIAGRAM MODEL SCPH 90004

    Hi since I changed the model I wanted to know the power button and the reset where I could connect it on a model scph 90004 please help me. :( I wanted to know if this switch scheme is okay obviously and a ps2 slim is also okay for a super slim?
  2. Soulheaven

    Question Project and advice on a portable model scph 79004

    Good evening hi this is my first time that I design a portable ps2, to be premised that I want to make a portable ps2 on a model scph 79004 so that I can make a cut to the motherboard and make it smaller, for the moment for experiment I have a card ps2 obviously not the scph 79004 model to...
  3. Jamehhhh

    Question PS2 Portable Help

    Hi All, I have decided I really want to have a go at creating my own Portable PS2. Unfortunately I do not have too much electronics experience, I only know the basics really. I also know this is a massive task for someone with my knowledge but I love a challenge! Now, the problem is I don't...
  4. GingerOfOz

    Worklog Ginger Does a PS2 Thing

    Uncertain what I'm going to title this project, so for now it's just a PS2 thing. I've never had a whole lot of drive to do a PS2 portable, just because I've never had any interest in the games for it. I bought a 79001 off of eBay shortly after Gman released the PS2 trimming guide, but it has...
  5. MomSpaghetti

    Worklog PS2 CLASSIC!

    Hello everyone, In this worklog, I'll be working on a project called the Ps2 classic. As the name indicates, It's going to be a mini version of the PS2 slim, just like the PS classic. It's a project that has been on my mind ever since i saw wesk's Noob Cube. Im not yet sure about the trim yet...
  6. MomSpaghetti

    Guide PS2 SMB: Use raspberry pi to load ps1 and ps2 games over SMB(+ Portability optimizations)

    Hello everyone, This is my first guide for this community. A small introduction into game loading methods of the ps2. There are 3 loading methods for the ps2: USB method. HDD method. SMB method. Usually, people opt to using the USB method because of the simplicity, all you need to do is...
  7. MomSpaghetti

    The Playstation Shield!

    Hello everyone! I'd like to present to you my Playstation shield!(took a while to come up with that name) It's a Playstation 2 portable with the advanced trim and relocation! Here are the specs: Playstation 2 SCPH-79003 board advance trimmed. 5" VGA Screen with an option to switch to AV to...
  8. MomSpaghetti

    Worklog Spaghetti's Playstation Shield portable!

    Hello everyone, I'd like to introduce you to my new playstation 2 portable that i've been cooking up for a while. I didn't even name it yet, but it'll probably be some generic one. Anyways, Welcome! With this playstation 2 project, it will have full compatibility, meaning any game that runs...
  9. Lampenman1

    Question Battery powering a PS2

    Hey, absolute beginner here! I want to build a PS2 portable (from a SCPH-75004), but I have some concerns. I'm looking to slowly work my way into portablizing the console, starting with making it independent from wall power. Now what I need to know is, how would I exactly do this? I know I'd...
  10. DannyRX

    Question an assembly problem

    Greetings people, i hope your good. Today I searched to see if I could give me a hand with this that happened to me about a week ago... my nephew had a PS2 Slim, he take it to repair and also mod it (I'm not sure that's how it's written), to play pirate games, and after 2 months, the guy...
  11. MomSpaghetti

    Worklog PS2 Laptop!

    Hello! Welcome to my PlayStation 2 laptop worklog, The reason behind this particular project is because of the PS2 model i have, SCPH-90004, It has a bigger motherboard than the usual 790001, Beside that, The Composite for some reason really shows a good picture and components cable doesnt work...
  12. Kells

    Question Micro Controller to control ps2

    I currently am working on improving my PlayStation 2 portable and I would like to be able to use a microcontroller instead of using a ps2 controller. I have a teensy 3.2 that I was hoping to use instead. Is there was any way to program this microcontroller to output what is needed to make a...
  13. Ron2797k

    Question ps2 scph50011

    hello, could someone help me? I have a ps2 fat scph50011 with motherboard gh26. I've had it for a long time, but about 5 years ago I stopped using it for lack of time. A few months ago I tried to use it again, but when I turned it on the image looked bad, so I restarted it but took out a spark...
  14. darkwing

    PIS2 - PS2 portable with build in SMB server

    So it's finally time to post this project in this section I believe. It's been quite a while since I started this project and it kind of evolve over the years. From thinking of using DVD drive all the way back in 2013 to looking into obscure hard drive setup for the slim, experimenting with...
  15. Matthew

    Release PS2+ Official Release

    Hello all, I finally feel that the Ps2+ is in a state that I can release to the public. The open-source project is located here: https://github.com/mcranford13/Ps2Plus. This project is meant to replace the PS2 Dualshock controllers and hopefully open the way for more ps2 portables. There has...
  16. SonicTheWerehog

    Question I need help with ps2 c-sync mod for VGA use.

    I have been trying for a long time to find a way to hook up my Playstation 2 to my LCD monitor. I've used the LM1881 circuit, but it didn't work due to the fact that it outputs c-sync instead of RGBHV. Then one day I found this thread: https://shmups.system11.org/viewtopic.php?f=6&t=60996 that...
  17. NahuelFlores

    Question Is this battery scheme well structured?

    Hello! As you saw in the title, I need help with this battery scheme. I need you to confirm your is well structured. To consider; each battery of the following scheme will be in an individual battery compartment. The batteries will be charged with a specific battery charger, so you will have to...
  18. NahuelFlores

    Question Can I charge three 18650 batteries with a 5v 1a charger?

    Hello! I'm in the middle of a PORTABLE PS2 project. This modification will use three 18650 batteries of 3.7 and 2200mAh to make 11.1v and then regulate it to 8.5v directly to the power port of the PS2. It should be noted that it is a SCPH-90010. I will charge the batteries with a 2.1mm jack...
  19. Soulheaven

    Question HELP PROJECT PS2 PORTABLE MODEL 77004

    Hello everyone, given that this is my first PS2 portable project, I wanted to know some tips on how to do this at both the video level and the sound level. First of all, at the time I wanted to increase, and to decrease the volume using keys without a potentiometer, only keys I wanted to know...
  20. Terrapaws

    Question PS2 Does not boot

    So I have just received a ps2 model 79001(the mobo layout is more like 79003 however). I applied DC power of 8.5v to the positive pin of the barrel jack and the negative to a ground near a mounting hole on the motherboard. So far I have been unable to get even an a red standby LED to show. I've...
Top