Search results

That actually did the trick! I was testing with working USB-A to USB-C cables and it wasn’t working. Based on your suggestion, I dug up a working USB-C to USB-C cable and it worked. No clue why but as long as it works I’m good. Thanks!

Well, I swapped out my bad SD-to-USB adapter and got somewhat strange results. The Good: With the new adapter, the SD card is now being read without issue when I turn on my Ashida. RVLoader boots up again, all my games show up, and I can play them with no issues. The Bad: Even with the new...

Oh wow! I actually didn't even know they made an upgraded version. I wish that had been available back when I made my Ashida. Thanks for the info!

Thanks! That's helpful. I'll check those out.

I had my Ashida working for a long time. Then, one day, I powered it on and got the below error message: RVLoader bootloader 01 Failed to initialize FAT FS! Is an USB drive plugged in? Press A to boot into priiloader I'll summarize my troubleshooting steps below but, to cut to the chase, does...

Hey Guys! I've had my Ashida working for several months now (thanks again to Wesk, Stiches, and everyone else that helped me!). I've recently decided to display my collection of handhelds so I bought some stands for them. I'd like a stand for the Ashida, too. I tried just sending the 'Ashida...

I had a bunch of weirdness until I let the batteries charge the first time for a full day. I just let it charge for 24 hours without touching it. That took care of a bunch of issues including the fan cutting out.

That doesn't look promising. Probably the only way to know for sure is to wire them up to something to test. Maybe sacrifice a cheap pair of wired headphones?

Well it took me about two months, but I think my Ashida build is finally done! Wesk, thank you so much for all of the work you did on this design! As a huge GC fan, having a real-hardware portable that has the same feel as a GC controller is amazing. It's something I never could've made on my...

Okay, I think placing Kapton tape over any potential contact points that were sticking out fixed it. I played for over an hour without issue which is way longer than it’s taken for the issue to come up before that. Hopefully, that did the trick.

Thanks. If these aren't showing you what you want to see, let me know.

So I noticed that I can get the stick drift to stop if I open the case and separate the two halves. So it has to be an issue with my build. I'm guessing that something inside is shorting SX and/or SY to ground somewhere along those circuits. I'm going to try to cover any contacts with kapton...

So I've been testing out my Ashida and I've noticed that I'm getting drift on my main thumb stick after around 20 minutes of gameplay. The direction of the drift seems to vary, but it's usually to the left. I've tried the Sticks Wizard in the RV Loader settings but the drift keeps coming back...

Okay, dumb question, but what screw size do I use for the eight screws that close the case? The Ashida BOM only mentions M2x5, which worked for stuff inside the case, but the screw holes for closing the case look smaller in diameter to me. I just don't want to strip out the screw holes on the...

Gotcha. Okay, that's really helpful. Maybe I'll just wire some temporary buttons up to bring the brightness up a tad before I close my Ashida up. Thank you!

Sorry if this isn't actually specific to the Ashida, but I seem to be having trouble adjusting screen brightness. Based on the RV Loader 1.6 forum thread, it looks like I should be able to adjust screen brightness by holding X+Z+DPad Up/Down. When I try to do that, I see the battery life...

Wiring them did the trick. Thanks! Now I just need to mess around with it to make sure there aren't any other issues before I call it finished.

Okay the last issue I'm noticing is that I get audio through the headphones but not through the speakers. I'm guessing that the little legs on the speakers aren't making pressure contact with the pads on the left and right Ashida boards (I didn't solder them). Should I try soldering wires from...

You're right. I just went with the colors in the diagram and didn't notice the difference indicated in the pin out. Problem solved. Thanks!

Yeah, it's weird. I'll try switching them around on the driver board pads tomorrow. It's getting late and I always end up messing things up more when I try to fix stuff too late at night. Thanks for your help!