Search results

It's hard to say what others haven't already and what isn't abundantly clear. Doom was just an amazing person. No matter if you only knew him for a day or a decade, if you talked with him daily or annually, he was always there to give actual advice or post dank memes. Usually the memes, to be...

Got my gift in today, it's pretty great. I rather like the datasheet and full printed manual also added, complete with Christmas Opossum. Thanks @StonedEdge! Unfortunately JPost wouldn't let you stay anonymous lool.

oo, another in the living in Tokyo club.

Wrote some HDL. Not too much, just went ahead and worked on the SPI slave data transceiver module for getting info to/from a computer using a USB<->SPI converter. It includes variable CPOL/CPHA settings as parameters in the module, I believe it seemed to work for all CPOL/CPHA unless I am...

Finished the PCB design. Still need to go and fully validate the schematics and ensure I'm not doing anything stupid before pulling the trigger on a PCB order. Kicad source files can be found here: https://github.com/kairotronix/kt_sound_pcb After design validation I'll get back to HDL.

Loool there's actually no FPGA in this revision. Just using a devkit for the time being and this will plug directly into it (it's a DE0-Nano board). Once the HDL is done I can run compilations until I find the cheapest FPGA it can feasibly run on and I'll make a final board with an integrated FPGA.

Full schematics in PDF form. May go and clean up a bit later 'cause some areas look a bit sloppy. On to generating all the footprints so I can actually begin laying this out. Also should probably generate a BOM cost soon.

Been working on the schematic capture portion of the design. Nearly done, need to work on the power supply. Attached are a couple schematics. DAC + Amp portion is using the same one Gman used for the audio amp for sale on the store. It was chosen because it was essentially the cheapest I2S amp...

So, with the help of @Gman I finally decided on a project (well, he decided for me). The idea is to make a synthesizer using purely (or at least primarily) digital logic in an FPGA. Ideally I'd also like to forgo the usage of wave-tables and mathematically derive some waveforms (notably sine)...

With all this talk of EDA software I can't help but peg in and say everyone should just join the Altium master race. Though it is a bit (really freaking) expensive. But dat smooth workflow. And iirc there's pretty good Solidworks integration. Regarding EAGLE, I personally didn't find it helpful...

I'm not super active, but BSEE from UIUC, working as electrical engineer for medical device company (lul guess i'll only do electronics work if you pay me). Would go for a higher degree but dem student loanz doe.

Depends on what you want. If you want ceramics glhf trying to find low quantities under 1 dollar a pop for a 100 uF. With tantalums you can get in that range, they're good for bulk capacitance, if you need to reduce transients you can throw a cheaper 0.1 uF or so ceramic in parallel.

There're a lot of options, it depends on how crazy you wanna go. I'd personally lay out a custom PCB using a dedicated chip from someone like Linear or TI, but that's more than most people would want to do. Btw, I live near by (Bellefonte) and work as an electrical engineer in the area and for...

If you make yourself look official enough they will, but I think TI started to be a bit more picky about who they give free samples to.

If you can spring a couple hundred I'd highly suggest a Metcal/OKI station. And I agree with the talks of Hakko. I use an FM203 occasionally at work and I dig it, though I would understand if it's a bit out of your budget. I've had mixed results with Tenma. Fairly good for the price point...

Too lazy to actually list everything out in a nice format. Here's the pcpartpicker my friend put together and I used: https://pcpartpicker.com/user/Kuro_Kenshi/saved/GfzgsY

Ah, I see you mentioned it before, now. I was at work when I saw some stuff, wasn't able to read the full thread. On another note, the LAN adapter and BBA have been cloned by some guy in Japan.LAN adapter was a CPLD interfacing an off-the-shelf chip. BBA was an FPGA interfacing a full on PCI...

There is an SD card GD-ROM replacement in existence. I can link when I'm not at work. But I think it's called GDEMU. Iirc the GD-ROM protocol is just PATA and like an explicit ripoff of CD standards with some extra stuff slapped on. In the document I have it's obvious they used a CD protocol...

I've got some documentation on the GD-ROM, was gonna start doing some stuff but real life and girlfriend and such seems to be taking up more time than I expected. I'll get to it eventually, though I am interested in seeing things done. My primary focuses in any sort of Dreamcast information in...

made some cookies